« previous next »
Pages: [1]   Go Down

Author Topic: Screwing own transom doublers during the epoxy set up?  (Read 2436 times)

Offline TFreeburg

  • Boson
  • ****
  • Posts: 434
Screwing own transom doublers during the epoxy set up?
« on: October 17, 2017, 06:55:37 AM »
I am now ready to install the doubled portions of the transom.  I plan to screw the boards together while they dry.  The lower doubler and the upper "wings" should not be a problem.  However, I have a kit from WCBoatWorks, and the motor doubler is massive!  I am thinking I should figure out a way to screw through the transom and up into the doubler, instead of trying to go down through the doubler into the transom.  This would entail either putting in a couple of screws and then flipping the entire wetted out transom, or wetting out the motor doubler and then putting the transom down on top of it.  In the first procedure I might make some mess, and in the second scenario I might screw up the alignment.  The only other option I can think of is to just drill deep - and I might even drill a few extra holes just to keep better seepage into this beast of a board.  Chuck, if you are reading this this - you build a great kit!
Any suggestions on this step?
Thanks in advance.
Snohomish Tom
Logged
Snohomish Tom
My goal: 25' Jumbo
First epoxy: 10/3/17
Flipped: 6/15/2019

Offline TFreeburg

  • Boson
  • ****
  • Posts: 434
Re: Screwing down transom doublers during the epoxy set up?
« Reply #1 on: October 17, 2017, 07:06:02 AM »
I meant screwing down the doublers.
Can't accurately type and/or proofread anymore... not that I was ever good at it.
Sheesh -
Logged
Snohomish Tom
My goal: 25' Jumbo
First epoxy: 10/3/17
Flipped: 6/15/2019

Offline Lyle

  • First Mate
  • *******
  • Posts: 1148
  • 21'4" Widebody. NJ South
Re: Screwing own transom doublers during the epoxy set up?
« Reply #2 on: October 17, 2017, 08:31:08 AM »
Tom,
 Maybe dry fit everything together, install and than remove 2 "locator" screws per piece. When gluing up, you screw into those 2 holes first to get back your dry fit alignment. Than you can flip,roll, or do anything you want without any slippage.
Lyle
Logged
Remain in neutral and move on to the next target
29.5 Seabright Skiff. Start Sep2018
21'4 Widebody. Class of 2009
17'6 Kayak 2013
18' Swampscott Dory 2012
16' River Runner Strip Canoe1996
19' Strip Canoe 1995

Offline TFreeburg

  • Boson
  • ****
  • Posts: 434
Re: Screwing down transom doublers during the epoxy set up?
« Reply #3 on: October 17, 2017, 11:09:26 AM »
Lyle,
Thanks for the feedback - I am considering that procedure; and then once I get a set of screws through the transom and into the doublers I may flip it back again so I can keep and eye on (and deal with) the seepage.  I am especially concerned about the small size of the slot where the floor is to fit in between the doublers.  I don't want any extra seepage filling into that slot during the bonding of the doublers.  In fact, I am considering making it slightly larger so that it will accept a floor board saturated with some epoxy and perhaps a layer of glass.

Any other comments on your experience fitting a floor into the slot between the doublers?

Tom
Logged
Snohomish Tom
My goal: 25' Jumbo
First epoxy: 10/3/17
Flipped: 6/15/2019

Offline gdwamsley

  • Second Mate
  • ******
  • Posts: 801
Re: Screwing own transom doublers during the epoxy set up?
« Reply #4 on: October 17, 2017, 03:42:12 PM »
Make the gap oversized.  Much easier to fill in extra space later than hog it out.

Sent from my SAMSUNG-SGH-I337 using Tapatalk

Logged

Offline TFreeburg

  • Boson
  • ****
  • Posts: 434
Re: Screwing dLyleown transom doublers during the epoxy set up?
« Reply #5 on: October 17, 2017, 06:09:40 PM »
Lyle,
I used your suggestion - with a good outcome.
Tomorrow I will pull out the screws and apply glass.
Tom
Logged
Snohomish Tom
My goal: 25' Jumbo
First epoxy: 10/3/17
Flipped: 6/15/2019
Pages: [1]   Go Up
« previous next »